ResCheck •
a
ciREScheck Software Version 4.6,2
Compliance Certificate
7-1:7147,61,--11 ii:',7
Project The Michaels Residence
Energy Code: 2015 IECC a a_
Location: Warren County, New York
TOWN OF QUEENSBURY
Construction Type: Single-family COMMUNITY DEVELOPMENT
Project Type: New Construction
Conditioned Floor Area: 5,191 ft2
Glazing Area 14%
Climate Zone: 6 (8499 HDD)
Permit Date: 2 March, 2017
Permit Number:
Construction Site: Owner/Agent: Designer/Contractor:
42 Grandview Drive NY
Queensbury, NY
Compliance: Passes using UA trade-off
Compliance: 7.8%Better Than Code Maximum UA: 578 Your UA: 533
The%Better or Worse Than Code Index reflects how close to compliance the house is based on code trade-off rules.
It DOES NOT provide an estimate of energy use or cost relative to a minimum-code home.
Envelope Assemblies
Gross Area Cavity Cont.
Assembly or R-Value R-Value U-Factor UA
Perimeter
Ceiling: Raised or Energy Truss 2,869 0.0 49.0 0.020 57
1st Floor Walls:Wood Frame, 16" o.c. 2,565 21.0 0.0 0.057 111
2x Home Office(C):Wood Frame:Double Pane with Low-E 23 0.280 6
lx Home Office(L):Wood Frame:Double Pane with Low-E 13 0.280 4
lx Powder(E):Wood Frame:Double Pane with Low-E 6 0.280 2
Foyer#1: Solid 21 0.170 4
2x Foyer(V):Wood Frame:Double Pane with Low-E 12 0.280 3
lx Foyer(W): Wood Frame:Double Pane with Low-E 9 0.280 3
lx Stair(E): Wood Frame:Double Pane with Low-E 6 0.280 2
lx Laundry(G): Wood Frame:Double Pane with Low-E 11 0.280 3
lx Alcove(G):Wood Frame:Double Pane with Low-E 11 0.280 3
Mud#2: Solid 19 0.170 3
Mud #4: Solid 19 0.170 3
3x Sun Room (P): Wood Frame:Double Pane with Low-E 19 0.280 5
2x Sun Room (S): Wood Frame:Double Pane with Low-E 40 0.280 11
2x Sun Room (R):Wood Frame:Double Pane with Low-E 35 0.280 10
2x Dining (N):Wood Frame:Double Pane with Low-E 36 0.280 10
lx Dining (U):Wood Frame:Double Pane with Low-E 34 0.280 10
Project Title: The Michaels Residence Report date: 04/12/17
Data filename: F:\Share\Design\Res-Check\On Your Lot\42 Grandview Drive.rck Page 1 of10
R
t
Gross Area Cavity Cont.
Assembly or U-Factor UA
Perimeter R-Value R-Value
Dining#3: Solid 19 0.290 6
Great Room #5: Solid 125 0.290 36
Master Bed #1: Solid 19 0.290 6
2x Master Bed (M):Wood Frame:Double Pane with Low-E 29 0.280 8
lx Master Bed (T): Wood Frame:Double Pane with Low-E 29 0.280 8
lx Master Bed (K):Wood Frame:Double Pane with Low-E 13 0.280 4
4x Master Bath (E): Wood Frame:Double Pane with Low-E 29 0.280 8
3x WIC(E): Wood Frame:Double Pane with Low-E 17 0.280 5
2x Home Office(G): Wood Frame:Double Pane with Low-E 21 0.280 6
2nd Floor Walls:Wood Frame, 16" o.c. 1,216 21.0 0.0 0.057 65
2x Loft(F):Wood Frame:Double Pane with Low-E 21 0.280 6
lx Loft(H):Wood Frame:Double Pane with Low-E 11 0.280 3
2x Bed #3 (AB): Wood Frame:Double Pane with Low-E 24 0.280 7
2x Bed#2 (A):Wood Frame:Double Pane with Low-E 16 0.280 4
lx Bed #2 (Q): Wood Frame:Double Pane with Low-E 11 0.280 3
Foundation Walls: Solid Concrete or Masonry 2,322 0.0 19.0 0.038 85
Wall height: 8.6'
Depth below grade: 7.6'
Insulation depth: 8.6'
3x Basement(X):Wood Frame:Double Pane with Low-E 17 0.280 5
lx Basement(AA):Wood Frame:Double Pane with Low-E 18 0.280 5
2x Basement(Y):Wood Frame:Double Pane with Low-E 17 0.280 5
lx Basement(Z):Wood Frame:Double Pane with Low-E 17 0.280 5
Garage Stair#4: Solid 19 0.170 3
Compliance Statement: The proposed building design described here is consistent with the building plans, specifications, and other
calculations submitted with the permit application.The proposed building has been designed to meet the 2015 IECC requirements in
REScheck Version 4.6.2 and to comply with the mandatory requirements listed in the REScheck Inspection Checklist.
h4...rD Q..3r.... j `it A-i--1 , Vram,L'D'E.--.1" if Q.(l
Name-Title Signat a Date
ik-1-1- e.-1/4.4... j, Pc:14-m,-,A-1--t o, p6_,
_ ,_
Project Title: The Michaels Residence Report date: 04/12/17
Data filename: F:\Share\Design\Res-Check\On Your Lot\42 Grandview Drive.rck Page 2 of10
a
REScheck Software Version 4.6.2
Inspection Checklist
Energy Code: 2015 IECC
Requirements: 0.0% were addressed directly in the REScheck software
Text in the "Comments/Assumptions" column is provided by the user in the REScheck Requirements screen. For each
requirement, the user certifies that a code requirement will be met and how that is documented, or that an exception
is being claimed. Where compliance is itemized in a separate table, a reference to that table is provided.
Section Plans Verified Field Verified
# Pre-Inspection/Plan Review Value Value Complies? Comments/Assumptions
&Req.ID
103.1, Construction drawings and ❑Complies
103.2 documentation demonstrate ❑Does Not
[PR1]1 energy code compliance for the
building envelope.Thermal ❑Not Observable
envelope represented on ❑Not Applicable
construction documents.
103.1, Construction drawings and ❑Complies
103.2, documentation demonstrate ❑Does Not
403.7 energy code compliance for
[PR3]1 lighting and mechanical systems. ❑Not Observable
ci, Systems serving multiple ❑Not Applicable
dwelling units must demonstrate
compliance with the IECC
Commercial Provisions.
302.1, Heating and cooling equipment is Heating: Heating: ❑Complies
403.7 sized per ACCA Manual S based Btu/hr Btu/hr ❑Does Not
[PR2]2 on loads calculated per ACCA Cooling: Cooling:
ka. Manual J or other methods ['Not Observable
Btu/hr Btu/hr
approved by the code official. ❑Not Applicable
Additional Comments/Assumptions:
1 High Impact(Tier 1) ! 2 ,Medium Impact(Tier 2) ! 3 'Low Impact(Tier 3)
Project Title: The Michaels Residence Report date: 04/12/17
Data filename: F:\Share\Design\Res-Check\On Your Lot\42 Grandview Drive.rck Page 3 of10
l
Section Plans Verified Field Verified
# Foundation Inspection Value Value Complies? Comments/Assumptions
& Req.10
402.1.1 Conditioned basement wall R- R- ❑Complies See the Envelope Assemblies
[F04]1 insulation R-value.Where interior R- R- ❑Does Not table for values.
insulation is used,verification
to
may need to occur during may Observable
Insulation Inspection.Not ❑Not Applicable
required in warm-humid locations
in Climate Zone 3.
303.2 Conditioned basement wall ❑Complies
[F05]1 insulation installed per DDoes Not
manufacturer's instructions.
te, ❑Not Observable
Not Applicable
402.2.9 Conditioned basement wall ft ft ❑Complies See the Envelope Assemblies
[F06]1 insulation depth of burial or ❑Does Not table for values.
distance from top of wall.
['Not Observable
ElNot Applicable
303.2.1 A protective covering is installed ❑Complies
[F011]z to protect exposed exterior ❑Does Not
insulation and extends a
ti
minimum of 6 in. below grade. ❑Not Observable
❑Not Applicable
403.9 Snow-and ice-melting system ❑Complies
[F012]2 controls installed. ❑Does Not
:Not Observable
❑Not Applicable
Additional Comments/Assumptions:
1 High Impact(Tier 1) 2 Medium Impact(Tier 2) 3 Low Impact(Tier 3)
Project Title: The Michaels Residence Report date: 04/12/17
Data filename: F:\Share\Design\Res-Check\On Your Lot\42 Grandview Drive.rck Page 4 of10
Section Plans Verified Field Verified
# Framing/Rough-In Inspection Value Value Complies? Comments/Assumptions
&Req.JD _
402.1.1, Door U-factor. U- U- ❑Complies See the Envelope Assemblies
402.3.4 DDoes Not table for values.
[FR1]1 DNot Observable
❑Not Applicable
402.1.1, Glazing U-factor(area-weighted U- U- ❑Complies See the Envelope Assemblies
402.3.1, average). ElDoes Not table for values.
402.3.3,
402.3.6, ❑Not Observable
402.5 ❑Not Applicable
[FR2]1
303.1.3 U-factors of fenestration products ❑Complies
[FR4]1 are determined in accordance ❑Does Not
with the NFRC test procedure or
taken from the default table. ❑Not Observable
❑Not Applicable
402.4.1.1 Air barrier and thermal barrier ❑Complies
[FR23]1 installed per manufacturer's ElDoes Not
instructions. ❑Not Observable
❑Not Applicable
402.4.3 Fenestration that is not site built EComplies
[FR20]1 is listed and labeled as meeting ElDoes Not
AAMA/WDMA/CSA 101/I.S.2/A440
or has infiltration rates per NFRC ❑Not Observable
400 that do not exceed code ❑Not Applicable
limits.
402.4.5 IC-rated recessed lighting fixtures ❑Complies
[FR16]2 sealed at housing/interior finish ElDoes Not
and labeled to indicate.2.0 cfm
leakage at 75 Pa. ❑Not Observable
❑Not Applicable
403.2.1 Supply and return ducts in attics ❑Complies
[FR12]1 insulated >= R-8 where duct is ❑Does Not
>= 3 inches in diameter and >=
R-6 where < 3 inches.Supply and [Not Observable
return ducts in other portions of ❑Not Applicable
the building insulated >= R-6 for
diameter>= 3 inches and R-4.2
for< 3 inches in diameter.
403.3.3.5 Building cavities are not used as ❑Complies
[FR15]3 ducts or plenums. ElDoes Not
❑Not Observable
❑Not Applicable
403.4 HVAC piping conveying fluids R- R- ❑Complies
[FR17]2 above 105°F or chilled fluids ElDoes Not
below 55°F are insulated to
3 ['Not Observable
❑Not Applicable
403.4.1 Protection of insulation on HVAC ❑Complies
[FR24]1 piping. ❑Does Not
['Not Observable
❑Not Applicable
403.5.3 Hot water pipes are insulated to R- R- ❑Complies
[FR18]2 >R-3. ElDoes Not
❑Not Observable
❑Not Applicable
403.6 Automatic or gravity dampers are ❑Complies
[FR19]2 installed on all outdoor air ❑Does Not
intakes and exhausts.
❑Not Observable
❑Not Applicable
1 a High Impact(Tier 1) 2 !Medium Impact(Tier 2) 3 !Low Impact(Tier 3)
Project Title: The Michaels Residence Report date: 04/12/17
Data filename: F:\Share\Design\Res-Check\On Your Lot\42 Grandview Drive.rck Page 5 of10
Additional Comments/Assumptions:
1 High Impact(Tier 1) 2 !Medium Impact(Tier 2) 3 !Low Impact(Tier 3)
Project Title: The Michaels Residence Report date: 04/12/17
Data filename: F:\Share\Design\Res-Check\On Your Lot\42 Grandview Drive.rck Page 6 of10
A1 Section Plans Verified Field Verified
# Insulation Inspection Value Vale Complies? Comments/Assumptions
&Req.ID
1
303.1 All installed insulation is labeled ❑Complies
[IN13]2 or the installed R-values ❑Does Not
provided. ❑Not Observable
❑Not Applicable
402.1.1, Wall insulation R-value.If this is a R- R- ❑Complies See the Envelope Assemblies
402.2.5, mass wall with at least 1/2 of the ❑ Wood ❑ Wood ❑Does Not table for values.
402.2.6 wall insulation on the wall ❑ Mass ❑ Mass ❑Not Observable
[IN3]1 exterior,the exterior insulation
requirement applies(FR10). ❑ Steel ❑ Steel ❑Not Applicable
303.2 Wall insulation is installed per ❑Complies
[IN4]1 manufacturer's instructions. ❑Does Not
[Not Observable
❑Not Applicable
Additional Comments/Assumptions:
1 High Impact(Tier 1) 2 !Medium Impact(Tier 2) 3 i Low Impact(Tier 3)
Project Title: The Michaels Residence Report date: 04/12/17
Data filename: F:\Share\Design\Res-Check\On Your Lot\42 Grandview Drive.rck Page 7 of10
Section Plans Verified Field Verified
Final Inspection Provisions Value Value Complies? Comments/Assumptions
&Req.ID
402.1.1, Ceiling insulation R-value. R- R- ❑Complies See the Envelope Assemblies
402.2.1, ❑ Wood ❑ Wood ❑Does Not table for values.
402.2.2, ❑ Steel ❑ Steel ['Not Observable
402.2.E pP[FI1] ❑Not Applicable
303.1.1.1, Ceiling insulation installed per ❑Complies
303.2 manufacturer's instructions. '❑Does Not
[F12]1 Blown insulation marked every
300 ft2. Not Observable
❑Not Applicable
402.2.3 Vented attics with air permeable ❑Complies
[FI22]2 insulation include baffle adjacent ❑Does Not
to soffit and eave vents that
extends over insulation. ['Not Observable
❑Not Applicable
402.2.4 Attic access hatch and door R- R- ❑Complies
(FI3]1 insulation >_R-value of the ❑Does Not
adjacent assembly.
['Not Observable
❑Not Applicable
402.4.1.2 Blower door test @ 50 Pa. <=5 ACH 50 = ACH 50 = ❑Complies
[F117]1 ach in Climate Zones 1-2,and ❑Does Not
<=3 ach in Climate Zones 3-8.
['Not Observable
❑Not Applicable
403.2.3 Duct tightness test result of<=4 cfm/100 cfm/100 ❑Complies
[F14]1 cfm/100 ft2 across the system or ft2 ft2 ❑Does Not
<=3 cfm/100 ft2 without air
handler @ 25 Pa. For rough-in ['Not Observable
tests,verification may need to ❑Not Applicable
occur during Framing Inspection.
403.3.2 Ducts are pressure tested to cfm/100 cfm/100 ❑Complies
[FI27]1 determine air leakage with ft2 ft2 ❑Does Not
either: Rough-in test:Total
leakage measured with a Not Observable
pressure differential of 0.1 inch ❑Not Applicable
w.g. across the system including
the manufacturer's air handler
enclosure if installed at time of
test. Postconstruction test:Total
leakage measured with a
pressure differential of 0.1 inch
w.g. across the entire system
including the manufacturer's air
handler enclosure.
403.3.2.1 Air handler leakage designated ❑Complies
[F124]1 by manufacturer at<=2%of ❑Does Not
design air flow.
['Not Observable
❑Not Applicable
403.1.1 Programmable thermostats ❑Complies
[FI9]2 installed for control of primary ❑Does Not
heating and cooling systems and
initially set by manufacturer to CI Not Observable
code specifications. ❑Not Applicable
403.1.2 Heat pump thermostat installed ❑Complies
[FI10]2 on heat pumps. ❑Does Not
[Not Observable
❑Not Applicable
403 Circulating service hot water ❑Complies
[FI11]2 systems have automatic or ' ❑Does Not
accessible manual controls.
❑Not Observable
❑Not Applicable
1 High Impact(Tier 1) ! 2 Medium Impact(Tier 2) 3 a Low Impact(Tier 3)
Project Title: The Michaels Residence Report date: 04/12/17
Data filename: F:\Share\Design\Res-Check\On Your Lot\42 Grandview Drive.rck Page 8 of10
Section Plans Verified Field Verified
Final Inspection Provisions Value Value Complies? Comments/Assumptions
&Req.ID
403.6.1 All mechanical ventilation system DComplies
[FI25]2 fans not part of tested and listed ❑Does Not
HVAC equipment meet efficacy
and air flow limits. ❑Not Observable
❑Not Applicable
403.2 Hot water boilers supplying heat DComplies
[FI26]2 through one-or two-pipe heating ❑Does Not
systems have outdoor setback
control to lower boiler water CI Not Observable
temperature based on outdoor ❑Not Applicable
temperature.
403.5.1.1 Heated water circulation systems DComplies
[FI28]2 have a circulation pump.The ❑Does Not
system return pipe is a dedicated -
return pipe or a cold water supply : ; ENot Observable
pipe.Gravity and thermos- ❑Not Applicable
syphon circulation systems are
not present. Controls for
circulating hot water system
pumps start the pump with signal .;
for hot water demand within the
occupancy. Controls
automatically turn off the pump
when water is in circulation loop
is at set-point temperature and
no demand for hot water exists.
403.5.1.2 Electric heat trace systems DComplies
[F129]2 comply with IEEE 515.1 or UL ❑Does Not
515.Controls automatically
adjust the energy input to the ❑Not Observable
heat tracing to maintain the ENot Applicable
desired water temperature in the
piping.
403.5.2 Water distribution systems that DComplies
[FI30]2 have recirculation pumps that ❑Does Not
pump water from a heated water
supply pipe back to the heated CI Not Observable
water source through a cold ENot Applicable
water supply pipe have a
demand recirculation water
system. Pumps have controls
that manage operation of the
pump and limit the temperature
of the water entering the cold
water piping to 104°F.
403.5.4 Drain water heat recovery units DComplies
[F131]2 tested in accordance with CSA ❑Does Not
B55.1. Potable water-side
pressure loss of drain water heat ['Not Observable
recovery units< 3 psi for ENot Applicable
individual units connected to one
or two showers. Potable water-
side pressure loss of drain water
heat recovery units < 2 psi for
individual units connected to
three or more showers.
404.1 75%of lamps in permanent DComplies
[F16]1 fixtures or 75%of permanent ❑Does Not
fixtures have high efficacy lamps.
Does not apply to low-voltage Not Observable
lighting. ENot Applicable
404.1.1 Fuel gas lighting systems have DComplies
[FI23]3 no continuous pilot light. EDoes Not
['Not Observable
ENot Applicable
1 High Impact(Tier 1) 2 Medium Impact(Tier 2) ; 3 Low Impact(Tier 3)
Project Title: The Michaels Residence Report date: 04/12/17
Data filename: F:\Share\Design\Res-Check\On Your Lot\42 Grandview Drive.rck Page 9 of10
Section
# Final Inspection Provisions Plans Verified Field Verified Complies? Comments/Assumptions
& Req.ID Value Value
401.3 Compliance certificate posted. ❑Complies
[F17]2 ,❑Does Not
❑Not Observable
❑Not Applicable
303.3 Manufacturer manuals for ❑Complies
[F118]3 mechanical and water heating ❑Does Not
systems have been provided.
['Not Observable
❑Not Applicable
Additional Comments/Assumptions:
1 High Impact(Tier 1) 2 Medium Impact(Tier 2) 3 Low Impact(Tier 3)
Project Title: The Michaels Residence Report date: 04/12/17
Data filename: F:\Share\Design\Res-Check\On Your Lot\42 Grandview Drive.rck Page 10 of10
. ,
2015 I0ECC EnergyEfficiency Certificate
Insulation Rating R-Value
Above-Grade Wall 21.00
Below-Grade Wall 19.00
Floor 0.00
Ceiling / Roof 49.00
Ductwork (unconditioned spaces):
Glass&Door Rating U-Factor SHGC
Window 0.28
Door 0.29
Heating&Cooling Equipment Efficiency
Heating System:
Cooling System:
Water Heater:
Name: Date:
Comments