Loading...
2005-544 TOWN OF QUEENSBURY 742 Bay Road,Queensbury,NY 12804-5902 (518) 761-8201 Community Development - Building & Codes (518) 761-8256 CERTIFICATE OF OCCUPANCY Permit Number: P20050544 Date Issued: Tuesday, October 09, 2007 This is to certify that work requested to be done as shown by Permit Number P20050544 has been completed. Location: 196 CHESTNUT RIDGE Rd Tax Map Number: 523400-290-000-0001-022-122-0000 Owner: MICHAEL CRAYFORD Tax Map Number: 523400-290-000-0001-022-122-0000 Applicant: MICHAEL CRAYFORD Owner: This structure may be occupied as a: Residential Alteration By Order of Town Board TOWN OF QUEENSBURY Issuance of this Certificate of Occupancy DOES NOT relieve the W property owner of the responsibility for compliance with Site Plan, Variance, or other issues and conditions as a result of approvals by the Director of Building&Code Enforcement Planning Board or Zoning Board of Appeals. Building Permit No.: 2005-544 APPLICATION FOR A TEMPORARY CERTIFICATE OF OCCUPANCY A TEMPORARY CERTIFICATE OF OCCUPANCY is hereby requested for the property located at: 196 Chestnut Ridge Rd For the following use(s): Residential Alteration I understand that if the conditions that follow are not met before the expiration date, the deposit is f ited. Z � Signature of Appl!cVr C, Dat A TEMPORARY CERTIFICATE OF OCCUPANCY is hereby ✓I APPROVED DISAPPROVED with the following conditions: 1) COMPLETE EXTERIOR FINISH 2) COMPLETE DECK 3) COMPLETE FIRE SEPARATION @ EXISTING BASEMENT& NEW REC. ROOM FEE: 10.00 DEPOSIT: W $100 RECEIVED ON: 9/19/07 p W 9/19/07 Director of Building & Code Enforcement* Date of Issuance** *This Certificate is NOT VALID unless signed by the Director of Building & Code Enforcement or his designee **This TEMPORARY CERTIFICATE OF OCCUPANCY expires 90 days from the Date of Issuance TOWN OF QUEENSBURY 742 Bay Road,Queensbury,NY 12804-5902 (518)761-8201 Community Development.-.Building&Codes (518) 761-8256 . BUILDING PERMIT Permit Number: P20050544 Ap h�ation Number. A20050544 j, Tax Map No: 523400-290-000-0001-022-122-00 0 Permission is hereby granted to: MICHAEL CRAYFORD For property located at: CHESTNUT RIDGE R in the Town of Queensbury,to construct or place at the above location in accordance with application together with o plans and other information reto filed and approved and in compliance with the NYS Uniform Building es and the Queensbury Z Ordinance. a of Construction Value Owner Address: 188 CHESTNUT RIDGE Rd Residential Alterat' n $150,000.00 QUEENSBURY,NY 12804-0000 Total Value $150,000.00 Contractor or Build'er's Name Address Ele 1 Inspection Agency Plans &Specifications 2005-544 2812 RESIDENTIAL ALTERATIO (ALTERATION TO BARN INTO LIVING SPACE) $281.20 PERMIT FEE PAID- THIS PERMIT EXPIRES: Sunday,August 12,2007 (If a longer period is required,an application for an extension must be made to the code Enforcement Officer of the Town of Queensbury before the expiration date.) Dated at the To o eens ,f� r'da�,August 12, 2005 SIGNED BY 4 OfV for the Town of Queensbury. Director of Building&`Code i4orcernent TOWN OF QUEENSBURY 742 Bay Road,Queensbury,NY 12804-5902 (518)761-8201 Community Development-Building& Codes (518) 761-8256 BUILDING PERMIT Permit Number: P20050544 Application Number: A20050544 Tax Map No: 523400-290-000-0001-022-122-0000 Permission is hereby granted to: MICHAEL CRAYFORD For property located at: CHESTNUT RIDGE Rd in the Town of Queensbury,to construct or place at the above location in accordance with application together with plot plans and other information hereto filed and approved and in compliance with the NYS Uniform Building Codes and the Queensbury Zoning Ordinance. Type of Construction Yalue Owner Address: 188 CHESTNUT RIDGE Rd Residential Alteration $150,000.00 QUEENSBURY, NY 12804-0000 Total value $150,000.00 Contractor or Builder's Name / Address Electrical Inspection Agency Plans&Specifications 2005-544 2812 RESIDENTIAL ALTERATION (ALTERATION TO BARN INTO LIVING SPACE) $281.20 PERMIT FEE PAID -THIS PERMIT EXPIRES: Saturday, August 12, 2006 (If a longer period is required,an application for an extension must be made to the code Enforcement Officer of the Town of Queensbury before the expiration date.) Dated at the Town of ueen ry; lda , A ust 12, 2005 SIGNED BY . for the Town of Queensbury. Director of Building&Code Enforcement C�R kc Check Residential Plan Review- bne& Two Family Dwellings {N/N/A (2)Full sets of plans Over 1,500 sq. ft.—Stamped Design Loads On Plans: 90 Wind Floor Loads 40 psf 70 Ground Snow Load Sleeping Areas and Attics 30 psf Calculations: Window Schedule With Glass Size Door Schedule/Main Entrance 36"Door Emergency Escape Or Bedrooms d Habitable Space Above/Below grade,5.7 sq. ft. ---- Grade,5.0 sq. ft. 24"(h)x 20"(w)min. 44"Max.Height above floor Residential Check Paperwork Compliance and Inspectors Checklist: OK Dampproofmg/Waterproofing Materials On Plans Foundation Drainage On Plans,if required 6"Drop in 10'Exterior Grade Framing Cross Section For Each Roof Line,Vertical Fire Stopping Every 10'Where --Required Ice and Snow shield 24"Inside Exterior Wall/24"Inside Knee Walls Platforms At Exterior Doors Stairway Headroom 6' 8'All Stairs 36"Width Stair Run and Rise Winder Run and Rise �f Spiral Not Allowed From 2 Story Smoke Detectors Battery Backup and Proper Location Bathroom Fixtures Proper Clearance Hall Width,36"min. Handrails More Than One Riser On Open Sides Railing and Guards>30"/Basement Stairs Included/Closed Risers More Than 4"in Ht. � Safety Glazing Notes For Required Areas Ttt Garage Fire Separation Garage Floor Sloped ..___ Attic Access Roof over 30"—2 "x 30"/Crawl Spaces 18"x 24"Access i Carbon Monoxide Detector Lowest Sleeping Level I Soil Test Results, if required Septic To Well Or Water Line Separation All Paperwork Signed WINDOW SCHEDULE Rr E D Job Site/Address: Date: 7 / 0 Owner: M(c1*96(- Application No. , TOW, Window Window window Unit or Rough Rough $Q,FT. SQ.FT 8Q.F—T- Clear Clear Special Hardware Number or Manufaturor Model/Type stook OpsnIn Opening Glass/Vis Egress/Ole Opening Opening or Instructions Letter on Name Numbs 9 Height Ibis Vent or Width In Height Plan call Width Light Opening Inches In Inches Isizo 7-o 10 I Z- 7�? 1 7. 0 4- 3o*10 13. z 16 , S -7 1 G -O 2- - 1-3 2 , 10 4 Ania -b k T- 410 5Z 9. 3 6- 4- So -7-S- Z - 2 I - I? Z- - (a -7 -0 0 3 - 2 - 5 06 N-01 OVU 0 r4 -rw Z 3C>TZ 3 S -4- 3© 15 7- o -3 -C> 'Z-.5 Example Entry A Anderson Narrollne 3062 3'2 6151/2 15030 8.36 4,01 --34—T 24 15/3510 Tempered Double 1131, it 11/18 Glazing Hung CTocuments and Settings\Suelooal Settings\TempWindow Schedula.doc Job Site Address: Date: Owner: M leHAEL Application No. File No. qq . � �. PLAN - 04- G�08 Building Permit — Calculation Sheet Natural Light, Ventilation & Emergency Egress Requirements Habitable Area of Req.Light Actual Req.Vent Actual ,r Sq.Ft. Remarks Room Room 8%of Room Light 4%of Room Vent Opening for in +,• Area Square Area Square x` Egress Square Footage Footage Feet K1TGtlr/ 30 x?B/g ?D ,3 !N/NG -22,64 41.8 61- 3 20,9 39- 34 /6,72s� GKERT 30 ibx 7.8/8 R60" 578,a 4G►29 63128 23, /4 30, /4 i4,72 2I�Si �28 ' DC-N 204, 14.32 4.5;38 B, i� 8,�2 4•Z9 sF ?zpfol 272, 2/.7G 42,37 14, 88 23, 39 /6,72 sc 33Vk 2a Y4' 136AWM ?&a !Gr(4 24,04 $. 32 /3,34 r r U\SueHemingway\Building.Per mit.FORM SWat.Light.Ventil.CalcuIati on.Sheet.doc Application for Permit- Septic Disposal System Town of Queensbury 742 Bay Road Queensbury NY 12804 (5181 161-8256 5 9 1. OWNER INFORMATION: .................... _ // Office Use Location of installation: Gin f 3 9t�Eti�'—n'a R�• "�" » File N-Mit. a V Tax Map No. Fee PaiA,�+ ' Owner's Name: Id,1 C Ne4t e 2 Address: (00 (� �rNyT +s7�� 2. INSTALLER'S NAME l Il C'/-t,�ti,6t- �2AYF�2� PHONE NO. _7 J1 S' � 3. RESIDENCE INFORMATION: (circle year of dwelling, indicate #bedroom(s) and multiply #of bedrooms with applicable gallons per bedroom to equal total daily flow) Year of House: No of Bedrooms x Computation = Total Dailv Flow 1980 or older x 150 gal/bdrm = 1980— 1991 x 130 gal/bdrm = 1991 —present 3 / x 110 gal/bdrm = 33 ca Garbage Grinder Installed yes V / no Spa or Hot Tub Installed yes f ! no 4. PARCEL INFORMATION: (circle applicable information& indicate measurements) Tovozral)hv Soil Nature Ground Water Bedrock or Impervious Material Domestic Water Supply Flat sand at what depth I at what depth §12:?11, Rolling loam #- Z 7 feet /V-A feetSteep slope c ay water supply `%slope other from any septic-system depth: absorption is /00 ft. other Percolation Test: (To be completed by licensed professional engineer or architect) Rate: minute per inch 5. PROPOSED SYSTEM: For New Construction: All individual sewage disposal systems must be designed by a licensed professional engineer or architect(unless installed in a Planning Board approved subdivision). Add 250 gallons to the size of the septic tank and leach field for each Garbage Grinder, Spa or Whirlpool Tub. Septic Tank: /2-5'0 gallon (min. size 1,000 gal.) Tile Field: each trench S-0 ft. Total System Length: Seepage Pit(s): number of size cf each: ft. by ft. Size of Stone to be used: # depth or thickness feat Bed System Size: x Alternative System: length and/or size 6. HOLDING TANK SYSTEM: (if required) Number of tanks: / Size of each: gallons /TOTAL Capacity: gallons ' t Note: Alarm System and associated electrical work must be inspected by a Town approved electrical inspection agency. 7. SIGNATURE &INFORMATION FOR RESPONSIBLE PERSON (please read) For your protection,please note that pursuant to Section 136-29 of the Code of the Town of Queensbury, any permit or approval granted which is based upon or is granted in reliance upon any material misrepresentation or failure to make a material fact or circumstance known by or on behalf of an applicant, shall be void. I have read the regulations with respect to this application and agree to abide by these and all requirements of the Town of Queensbury S nitary Sewa e Disp al Ordinance. �- , 7 jz C) Signature of respon vele person Date Town of Queensbury Sewers and Sewage Disposal Chapter Appendix C ABSORPTION FIELD SEPARATION REQUIREMENTS i r F43iN#� N1ft.w�.. aK yr�t�'At- �a WMw: -" i t wsxtc Appendix C ABSORPTION FIELD SEPARATION REQUIREMENTS PO �J�t.R"41G�inAT r } V� Hd A. iiIGHWAY �igh"W Superintendent DEPARTMFIqT Home(518)798-5127 742 Bay Road - Queensbury NY 12804 Michael F. Travis Office Phone: (518) 761-8211 DePutY High"Superintendent Fax: (518) 745-"" DRIVEWAY PERMIT ._t U DATE: 7 1z o APPLICANT NAME: /z119 y/__R-',—\ TELEPHONE NO.: 7 99' /9 9 7 — '14 S• lr o n v.=f QA 2N, ADDRESS TO BE INSPECTED: 4, 3r3 �hEs;ni✓ /L+��f >. v '`%�' j�$ RETURN ADDRESS: 4N5 l I7 Si N✓T -� /cam . c�r�y Applicant must show exact location and width of driveway(s)to be connected to the highway by placing stakes at the specified location. The Superintendent of Highways of the Town of Queensbury has reviewed this application. The following action has been taken: STEP 1: ( )Preliminary Approval NEED: ( )Slight Swale O Level with the road ( )Deep Swale Size pipe to be used(if necessary) ( )12„ ( )15" ( )IS- ( )24" ( )36„ Preliminary inspection completed by DATE Approval by Highway Supt. Deputy Supt Upon completion,please resubmit this approved permit for a final approval. STEP 2: ( )Final Approval O Rejected DATE: Richard A. Missita,Highway Superintendent Principal Structure Budding Permit Application Application & Plans subject to review before issuance of a valid permit for cons ction. Instructions: A permit must be obtained before beginning construction. No inspections, ag unAtht applicant has received a valid building permit. All applicants' spaces on this application mu and must appear on the application form. Applicant/Builder r cHAe� C2+gYF� Owner: sAM6 Address: SV CFrEST"NyT t?,'Z6g ✓2e� - Address: Q v pus J2 C - Home Phone: 1�d` 7 Home Phone: Email Address: Email Address: _ Cell Phone: Cell Phone: >,. FAX Phone: 0 C1 FAX Phone: J1111. Person responsible for supervision of work with respect to building and codes compli R,:, Name: Address: 8% 36 Nix— Ta %e 8Phone "` . Location of proposed construction: Lot No. _? Q Legal Address: Tax Map Number: / /O Subdivision Name: Hr C-6-S Estimated Cost of Construction: $ 10; ®0 f3 Proposed construction is for: i- Residential Use __._Commercial Use Name of Business: If proposed construction is an addition, what will use of new addition be? New Addition Alteration Proposed Construction 10 Floor 2nd floor Other Total Proposed structure (Occupancy Type) Sq. Ft. sq.ft. Sq. Ft. Square feet Height Ft. &in. Sin le-Family Dwelling Z-Zo4 G'a S Z®/Z E-f1S77n/f.— Two-Famit Dwelling Townhouse Multifamily Dwelling Number of Units: Office Mercantile manufacturing Other: Attached Garage 1, 2, 3 Type of Heating System: Electric, Oil, Gas, Wood, Forced Hot Air, Baseboard, Other: f a fireplace and/or woodstove are being installed, please refer to a separate application. Applications are subject to Zoning Administrator, Code Compliance, and Structural Plan review. the Building and Codes Office will allow commencement of your proposed project only after ssuance of your permit. )eclaration: Please sign below after you have carefully read the statement: o the best of my knowledge, the statements contained in the application, together with the plans and pecifications submitted, are a true and complete statement of all proposed work to be done on the described )remises and that all provisions of the Building Codes, the Zoning Ordinance, and all other laws pertaining to the )roposed work shall be complied with,whether specified or noted, and that such work is authorized by the owner. urther, it is understood that I/we shall submit prior to a Certificate of Occupancy or Certificate of Compliance >eing issued, as requested by the Zoning Administrator or Director of Building and Codes, n As-Built Survey fy a censed surveyor, drawn to scale, showing actual location of all w c stru ion )ate: 1 Z oS Applicant/Builder Signature: =� he application of dated is hereby approved and >ermission granted for the construction, reconstruction or alteration a building/and or accessory structure as set �rth above. ]� Date: uthorized Signature: ► `L \Sue Hemingway\Building.Permit.PORMS\Principal Structure Permit Application.doc V:12/14/04 /--�, - ;> �--) s tu /�� - �)eAj- - Queensbury Building & Code Enforcement - Residential F' al Inspection Office No. (518)761-8256 Arrive: a m e a Date Inspection request received: Inspector's Initials: NAME: E IT#: LOCATION: �` ijD TE: TYPE OF STRUCTURE: Comments Yey No N/A —T-- i ? Cs,) tiT1gJ1 BuildingNumber/Address visible from road 10 p ChimneyHeight/"B"Vent/Direct Vent Location ^ �Q Fresh Air Intake 3 inch Pl bin Vent through roof minimum 6 inches 0o Co let /Exterior Finish Com lete r Platform at 1 exterior doors � Guards at stairs,decks,patios more than 30 inches above grade 2 ��j�,� �E Fy Guard at stairwell at 34 inches or more Guard at deck,porches 36 inches or more 2 �cQ RRRT161� �— �c 11f11�1 Handrail Termination at Newell Post or Wall �j R�c MST ttJE c� Interior/Exterior Railings 34 inches to 38 inches � G!'� Interior Handrails @ stairs 2 or more risers Grade away from foundation 6 inches with 10 feet 6 inch clearance to sill plate Gas Valve shut-off exposed/regulator 18 inches above grade Interior privacy/trim/doors/main entrance 36 inches Bathroom/Kitchen watertight Safety glazing/Window in stairwells safety glazingi GC' �p 1 OE Interior Smoke Det ors: / Every level: wo Every Bedroo Outside every bedroom arpw. / Inter Connected: ✓ Battery backup: Carbon Monoxide Detector Attic access 30 inches x 22 inches x 30 inches(height)in accessible area Crawl Spaces 18 inch x 24 inch access, 1 s .ft.-150 s .ft.vents Bathroom Fans,if no window Plumbing fixtures Foundation insulation Floor truss,draft stopping finished basement 1,000 s .ft. Emergency egress below grade Gas Furnace shut-off within 30 feet or within line of site Oil Furnace shut-off at entrance to furnace area Furnace/Hot Water Heater operating Low water shut-off boiler Relief Valve(s)installed/Heat Trap/Water Temp 110 Enclosed Stairs Sheetrock Underside minimum%2"Gypsum Basement stairs closed rise>4 inches Garage Floor Pitched Garage fireproofing/3/.hour fire door/door closer Duct work Sealed properly Gas Logs in Sealed or Glass Enclosure Final Electrical Final Survey Plot Plan As Built Septic System/Sewer Dept.Inspection Sticker Site Plan /Variance required Flood Plain Certification,if re 'red Oka to issue C/C or C/O Temporary/P r nent] L:\Building&Codes Forms\Bui ing&Codes\Inspection Forms\Residential Final Inspection Form revised 100405.doc /J -2- Queensbury Building & Code Enforcement - eE: �F'.nal Inspection Office No.(518)761-8256 "� Arrive: ,!L.�Date Inspection request received: `"1Inspector's InitiaNAME: "U LOCATION: j4 16-7 TYPE OF STRUCTURE: Comments Ye No N/A Building Number/Address visible from road Chimney Height/"B"Vent/Direct Vent Location Fos Lance;� T�YE o F Fresh Air Intake � 3 inch PlumbingVent through roof minimum 6 inches Roof Complete/Exterior Finish Com lete C�t�Pt-ESE r �D� Platform at all exterior doors F'%*�t t*A Guards at stairs,decks, atios more than 30 inches above grade p F Q� Guard at stairwell at 34 inches or more V001, Guard at deck,porches 36 inches or more Handrail Termination at Newell Post or Wall Interior/Exterior Railin s 34 inches to 38 inches Interior Handrails @ stairs 2 or more risers Grade away from foundation 6 inches with 10 feet 6 inch clearance to sill late Gas Valve shut-off exposed/regulator 18 inches above grade Interior privacy/trim/doors/main entrance 36 inches A Bathroom/Kitchen watertight � � . Safe glazing/Window in stairwells safetyglazing Interior Smoke De tors: Every level: Every Bedroom: ✓ ��1J, Outside every bedroom tea: Inter Connected: Battery backup: Carbon Monoxide Detector Attic access 30 inches x 22 inches x 30 inches(height)in accessible area Crawl Spaces 18 inch x 24 inch access, 1 s .ft.-150 s .ft.vents 01 Bathroom Fans,if no window Plumbing fixtures �1oT� Go Foundation insulation Floor truss,draft stopping finished basement 1,000 s .ft. -� Emergency a ess below grade Gas Furnace shut-off within 30 feet or within line of site Oil Furnace shut-off at entrance to furnace areaQ-t�M� Fumace/Hot Water Heater operating o � Low water shut-off boiler Relief Valves installed/Heat Trap/Water Temp 110 Enclosed Stairs Sheetrock Underside minimum%a"Gypsum Basement stairs closed rise>4 inches Garage Floor Pitched Garage fireproofing/%hour fire door/door closer A4, Duct work Sealed properly Gas Logs in Sealed or Glass Enclosure Final Electrical �-�� Final Survey Plot Plan �5 As Built Septic System/Sewer Dept.Inspection Sticker Site Plan /Variance required Flood Plain Certification,if required ����t:�)6 Okay to issue C/C or C/O Temporary/Permanent , L:\Building&Codes Forms\Building&Codes\Inspection Forms\Residential Final Inspection Form revised 100405.doc Town of Qaeembury Fire Marshal 742 Bay Road Qaeensbury,NY 12904 7614rM/761-SM � fax 745-U37 Factory Built Gas FinWace/Stove Inspection t gort Notice:New York State requires that all UL Listed,factory built appliances be installed according to the instructions specifications contained in the Installation Manual accompanying the appliance.No deviation from the manufactu is instructions or specifications is allowed. 1 Permit# Schedule Ins lion q I Ti pm ytime Name dress Gl �t� gh Appliance M cturer Model# Direct vent Factory Built Chimney Fine Size Double Wall 'Triple Wall insulated Yes No N/A Comments Floor Protection Clearances to Combustibles (all sides) Firestop(s) Vertical Chase Wall Penetration Vent Clearances to Combustibles Vent/Chimney Termination Chimney height must be 3 feet above roof penetration;2 feet above any combustible construction within 10 feet Gas Shut-off Valve Combustion Air Hearth Extension (if any) Mantel Helot above Vp opening Witness Operation Tank Placement(if LP) �� Y�w Pink—Fb v Mar" "s Final Survey Inspection Dept. of Community Development Town of Queensbury 742 Bay Road Queensbury,NY 12804 Date received: L3 101 NAME: LOCATION: l 43A PERMIT#: 05-�T4 Final Survey Plot Plan Approved Denied The attached final survey has been received by the Dept.of Community Development. Upon review the survey Craig Brown,Zoning Administrator 0 Notes: EC RFP 013200("1 TOWN OF WEE URY L.\SueHemingway\Building.codes.Inspection.FORMSTinai Survey Zoning Administrator.doc MAP REFERENCE: CTL MAP OF A SUBDIVISION MADE FOR CRAYFORD & HIGGS �'-- DATED JULY 25, 1997 LAST REVISED JANUARY 21, 1998 BY VAN DUSEN & STEVES LAND SURVEYORS SUBDIVISION MODIFICATION OF LOT 3 DATED APRIL 29, 2004 0 LAST REVISED JULY 13, 2004 A ; � LOT 4 I -04 S810,5 "E All 657.021 � SZ: AO o"1Q1 LOT 3B N �s° 134,294 sq. ft. 3.08 acres / 923� �?F A.C.O.E. � WETLANDS Cb o O CD 593. 70 LOT 3A O C2 _00 z Q0 c cooF �N �(n o M W -� 3fi# 01 LAN Date: MAY 6, 2005 a n D u '� �Cl 'INAInH Rm ALTERATNN OR ADDITION TO A SumEY Scale 1"=50' YAP 6EA1M A LCENSED LAND SURYEraRs SEAL IS A Map of a Survey made for Q ,. ` WILA,ICR W SECTOR 7209.M-DItl190N 2.OF THE `x. NEM YW STATE EDWAMM LAW ONLY COPIES FROM THE OPoGMAL Or TTA5 SURVEY S t e v e s MAR o�ANOWtIGNAL OF CNSKNM E S— 1 SEAL SHALL�Cp19DOED m BE VIND TRIG COPES' 'L �'��I `WIN Michael Crayford THIS INCI C Y WAS PREPARED N LAW ,I TIE E70STNO CODE OF PRACTICE FOR LAID 9URYEhORS ADOPTED Land Surveyors LAW "DIM STATE A TICATION SHALL LAND StNYETORS SAID OEITiiN'.A1NIN5 SHALL RlN OILY TO THE PERSON FOR WHOM THE SIFYEY IS PREPARED.AND ON HIS BEHALF TO THE TILE COMPANY.OON INIMENTAL 169 Haviland Road Queensbury, New York 12804 TOTIC A�LENDING AM Town of Queensbury, Warren County, New York 4/1%7 UPDATED SURVEY TO THE A951GNEM Or THE LENDING IN5TRUTM.• CRAYFORD C-1506 (518) 792-8474 New York Lic. No. 50135 NO. DATE DESCRIPTION DWG. NO. 97092-313 290-1- COMMONWEALTH ELECTRICAL INSPECTION SERVICE,INC. Main Office 176 Doe Run Road-Manheim,PA 17545 MUNICIPAL CERTIFICATE - ELECTRICAL APPROVAL 1,ermit No....'".�................v.I.....L-1-Cert. N2 3142Cut-in Card No.................................... :)wner...........In ..................................................................... Location..Z?A......6!��57—/Glg 7— 12-1.0.1��................. .. ............................... .............................. .... ........ 4, 4-1 77S ....q[ristallation Consisting of.. . .....5*0.1..x6�j ......**'*****../............. D/w,...... ... ................................................................................................................. ................................................................................................................................................................................. Installed By........... ...........................................Lic.No.................................................. ....................... ......... The conditions following governed the issuance of this certificate,and any certificate previously issued i, -ancelled:- This certificate only covers the electrical equipment and installation conditions as of date. Upon th( introduction of additional equipment or alterations,application shall be promptly made for inspection. Inspectors of this Company shall have the privilege of m"nspections at any time, and if it; it t 0 f I rules are violated,the Company shall have the right p rexi ke tivis cepri ica tj e Date...... .................. INSPECTOR./j.............................................................................. Member N.F.P.A.,I.A.E.I. Rough Plumbing / Insulation Insoection Re ort Office No. (518) 761-8256 Date Inspection requ re iv OV) 13IV/ Queensbury Building & Code Enforcement Arrive: part: arr��� 742 Bay Road, Queensbury, NY 12804 Inspector's Initi Is. NAME: �� L�e-� PER #: CAS—SV 54 LOCATION: � �d �/" INSP CT ON: L �ke TYPE OF STRUCTURE: U Y N N/A Rough Plumbing Nail Plates Plumbing Vent/ Vents in Place 1 1/2 inch minimum Drain Size Washing Machine Drain 2 inch minimum Cleanout every 100 feet change of direction Pressure Test Drain / Vent Air/ Heada �=> � 5 P.S.I. or 10 ft. above highest connection for 15 minutes Pressure Test Water Supply Piping " Air/ Head �� 5 .I for 15 minutes nsulation Residential Check Commercial CheckILL ro er Vent Attic Vent Duct/ Hot Water Piping Insulation If required unheated spaces izLZ> Combustion Air Supply for Furnace Duct work sealed properly / No duct tape COMMENTS: C� C—a LZAAJAx---,� kzAQ- LAPam Whiting\Building&Codes\Inspection Forms\Rough Plumbing Insulation Report.revised Nov 17 2003.doc Revised February 15,2005 Y- W a-t1--- Rough Plumbing / Insulation Inspection Report Office No. (518) 761-8256 Date Inspectoon reque re i Queensbury Building & Code Enforcement Arrive: `I-k a /p epart: a 742 Bay Road, Queensbury, NY 12804 Inspector's Initial 2 NAME: PER IT #: LOCATION: INSPECT ON: !© �7 0� TYPE OF STRUCTURE: Y N N/A Rough Plumbing Nail Plates •� Plumbing Vent/ Vents in Place 1 1/2 inch minimum Drain Size Washing Machine Drain 2 inch minimum Cleanout every 100 feet change of direction Pressure Test Drain / Vent Air / Head 5 P.S.I. or 10 ft. above highest connection for 15 minutes Pressure Test Water Supply Piping Air / Head 50 P.S.I for 15 minutes nsulation Residential Check/ Commercial Check Pro er ent Attic Vent Duct / Hot Water Piping Insulation If required unheated spaces Combustion Air Supply for Furnace Duct work sealed properly / No duct tape COMM C)'J�C* D L:�Pam Whiting\13uilding&Codes\Inspection Forms\Rough Plumbing Insulation Report.revised Nov 17 2003.doc Revised February 15,2005 Rough Plumbing / Insulation Inspection Repor Office No. (518) 761-8256 Date Inspection request received; eensbu Buildingv&Code Enforcement Arrive: = a e m=''F 742 Bay Road, Queensbury, NY 12804 Inspector's Initials. NAME: `— )-b �I/� 'PERMIT #: LOCATION: 1 l� INSPECT ON: 0!o TYPE OF STRUCTURE: ,•� IY N N/A PVC: R-1,R-2,R-3,R4 Drain/Vents Cast Iron,Copper Drain/Vent/Comm. Plumbing Vent/Vents in Place Rough Plumbing/Nail Plates 1 % inch min.Drain Size Washi rain 2 inch min. ad or Air Supply Te Drain and Vents 5 PSI or 10 feet a hjest n for 15 minutes Cleanout every 100 feet/change of direction Water Supply Piping Cooper Commercial Cooper, CPVC,Pex One and Two-Family Insulation/Residential Check/Commercial Check Proper Vent,Attic Vent Duct/Hot Water Piping Insulation If required unheated spaces Combustion Air S!,tpplyfor Furnace Duct work sealed proper! /No duct tape COMMENTS: L:\SueHemingway\$uilding.Codes.Inspection.FORMS\Rough Plumbing Insulation Report.doc November 17,2003 "I have seen or observed, or believe 1 saw evidence of, all objects such is houses, tip-1 t,,Gwices, etc., sh nt that I have "A odth on the diagram S N AI'U R E LO I�C C:) i V) 0i Z5 P _ ROOF-CEILING CONSTRUCTION FIGURE R804.3.10(2)-R808.1 2 IN.CLIP ANGLE WITH FOUR SCREWS EACH LEG BOTH SIDES BUILT-UP HEADER AND TRIMMER JOISTS SHALL OF CONNECTION BE SCREWED TOGETHER AT 24 IN.O.C.MAX. THROUGH TOP AND BOTTOM FLANGES(TYP.) 0 0 0 0 0 0 BUILT-UP HEADER JOISTS SHALL CONSIST OF A C-SECTION INSIDE A TRACK SECTION 0 0 0 0 4 SCREWS EACH LEG OF CLIP ANGLE o 0 0 0 0 (BOTH SIDES OF CONNECTION) MIN.LENGTH=JOIST/RAFTER WEB DEPTH MINUS 1/2 IN. 0 JOIST/RAFTER BUILT-UP HEADER JOISTS SHALL CONSIST OF A C-SECTION INSIDE A TRACK SECTION For SI:1 inch=25.4 mm. FIGURE R804.3.10(2) HEADER TO TRIMMER CONNECTION WW SECTION R806 .. - ROOF VENTILATION R806.1 Ventilation required. Enclosed attics and enclosed The rough-framed opening shall not be less t an 22 inches by rafter spaces formed where ceilings are applied directly to the 30 inches(559 mm by 762 mm)and shall be located in a hall- underside of roof rafters shall have cross ventilation for each way or other readily accessible location.A 30-inch(762 mm) separate space by ventilating openings protected against the en- minimum unobstructed headroom in the attic space shall be Provided at some point above the access opening.See Section trance of rain or snow.Ventilating openings shall be provided with corrosion-resistant wire mesh, with 1/8 inch (3.2 mm) entM13 is located for access requirements where mechanical equip- with minimum to 1/4 inch(6.35 mm)maximum openings. went s located in attics. R806.2 Minimum area. The total net free ventilating area shall not be less than 1 to 150 of the area of the space ventilated SECTION R808 INSULATION CLEARANCE except that the total area is permitted to be reduced to 1 to 300, provided at least 50 percent and not more than 80 percent ofthe R808.1 Combustible insulation.Combustible insulation shall required ventilating area is provided by ventilators located in be separated a minimum of 3 inches(76 mm)from recessed the upper portion of the space to be ventilated at least 3 feet lighting fixtures,fan motors and other heat-producing devices. (914 mm)above eave or cornice vents with the balance of the required ventilation provided by eave or cornice vents.As an Exception: When heat-producing devices are listed for lesser clearances, combustible insulation complying with alternative,the net free cross-ventilation area may be reduced the listing requirements shall be separated in accordance to 1 to 300 when a vapor barrier having a transmission rate not exceeding 1 perm(57.4 mg/s•m2•Pa)is installed on the warm with the conditions stipulated in the listing. side of the ceiling. Recessed lighting fixtures installed in the building thermal envelope shall meet the requirements of Section N1101.3. R806.3 Vent clearance. Where eave or cornice vents are installed,insulation shall not block the free flow of air.A mini- mum of a 1-inch(25.4 mm)space shall be provided between the insulation and the roof sheathing at the location of the vent. SECTION R807 ATTIC ACCESS RESIDENTIAL CODE OF NEW YORK STATE 243 Permit Number REScheck Compliance Certificate Checked By/Date New York State Energy Conservation Construction Code REScheckSoflware Version 3.5 Release le Data filename:Untitled.rck PROJECT TITLE:Michael Crayford COUNTY: Warren JUL � � 2005 STATE:New YorkC d HDD: 7635t , Non-ElectricCONSTRUCTION ched 1 or 2 Family HEATING TYPE: DATE: 06/21/05 DATE OF PLANS: June 05 PROJECT DESCRIPTION: Single Family Residence COMPLIANCE:Passes FILE Copy Maximum UA=569 Your Home UA=437 23.2%Better Than Code(UA) Gross Glazing Area or Cavity Cont. or Door Perimeter R-Value R-Value U-Factor UA Ceiling l:Flat Ceiling or Scissor Truss 2242 38.0 0.0 67 Wall 1: Wood Frame, 16"o.c. 3203 29.0 0.0 132 Window 1:Wood Frame:Double Pane with Low-E 275 0.340 94 Door 1: Solid 50 0.200 10 Door 2: Glass 176 0.340 60 Floor 1: All-Wood Joist/Truss:Over Unconditioned Space 2242 30.0 0.0 74 Furnace 1:Forced Hot Air, 84 AFUE COMPLIANCE STATEMENT: The proposed building represented in this document is consistent with the building plans, specifications,and other calculations submitted with this permit application. The proposed systems have been designed to meet the New York State Energy Conservation Construction Code requirements. When a Registered Design Professional has stamped and signed this page,they are attesting that to the best of his/her knowledge,belief,and professional judgment,such plans or specifications are in compliance with this Code. Builder/Designer Date Z/ 4,5" cr 00 a c$�, �pg0a8 mom NNW Cbec' ist onstructt°n Ode [ InspeCtion heck hero Conserva Lion C k State E Ljew Yor Version 3.5 Release I REScheckSo ware V XTE:06/21/05 PROIECT TITLE.Michael Crayford Bldg. I Dept. I Use I Ceilin insulation I 38.0 cavity I gs: 1.Flat Ceiling or Scissor Truss?R Ceiling Comments: I I Above-Grade Walls: [ ] I 1. Wall 1:Wood Frame, 16"o.c.,R-29.0 cavity insdatiOn Comments: I Windows: [ ] I 1. Window 1: Wood Frame:Double Pane with Low-E,U-factor:0.340 For windows without labeled U factors,describe features: #Panes Frame Type Thermal Break?[ )Yes[ )No Comments: i Doors: [ ] I 1. Door l: Solid,U-factor:0.200 Comments: [ ] I 2. Door 2: Glass,U-factor:0.340 Comments: Floors: [ ] I 1. Floor 1:All-Wood Joist/Tniss:Over Unconditioned Space,R-30.0 cavity insulation Comments: I I Heating and Cooling Equipment: [ ] I 1. Furnace 1:Forced Hot Air,84 AFUE or higher Make and Model Number I Air Leakage: [ ] I Joints,penetrations,and all other such openings in the building envelope that are sources of air leakage must be sealed. [ ] I Recessed lights must be 1)Type IC rated,or 2)installed inside an appropriate air-tight assembly with a 0.5"clearance from combustible materials. If non-IC rated,the fixture must be installed with a 3"clearance from insulation. I Vapor Retarder: [ ] I Required on the warm-in-winter side of all non-vented framed ceilings,walls„and floors. I Materials Identification: [ l I Materials and equipment must be installed in accordance with the manufacturer's installation instructions. [ ] I Materials and equipment must be identified so that compliance can be determined. [ ] I Manufacturer manuals for all installed heating and cooling equipment and service water heating equipment must be provided. [ ] I Insulation R values,glazing U-factors,and heating equipment efficiency must be clearly marked on the building plans or specifications. I + Duct Insulation: [ ] Supply ducts in unconditioned attics or outside the building must be insulated to R-11. [ ] Return ducts in unconditioned attics or outside the building must be insulated to R-6. [ ] ( Supply ducts in unconditioned spaces must be insulated to R-11. [ ] Return ducts in unconditioned spaces(except basements)must be insulated to R-2. Insulation is not required on return ducts in basements. 1 Duct Construction: [ ] I All joints,seams,and connections must be securely fastened with welds,gaskets,mastics (adhesives),mastic-plus-embedded-fabric,or tapes. Duct tape is not permitted. Exception:Continuously welded and locking-type longitudinal joints and seams on ducts operating at less than 2 in.w.g. (500 Pa). [ ] Ducts shall be supported every 10 feet or in accordance with the manufacturer's instructions. [ ] Cooling ducts with exterior insulation must be covered with a vapor retarder. [ ] Air filters are required in the return air system. [ ] The HVAC system must provide a means for balancing air and water systems. I Temperature Controls: [ ] Each dwelling unit has at lesat one thermostat capable of automatically adjusting the space temperature set point of the largest zone. 1 Electric Systems: [ ] Separate electric meters are required for each dwelling unit. Fireplaces: [ ] Fireplaces must be installed with tight fitting non-combustible fireplace doors. [ ] Fireplaces must be provided with a source of combustion air,as required by the Fireplace construction provisions of the Building Code of New York State,the Residential Code of New York State or the New York City Building Code,as applicable. Service Water Heating: [ ] Water heaters with vertical pipe risers must have a heat trap on both the inlet and outlet unless the water heater has an integral heat trap or is part of a circulating system. L ] I Insulate circulating hot water pipes to the levels in Table 1. I Circulating Hot Water Systems: [ ] Insulate circulating hot water pipes to the levels in Table 1. I Swimming Pools: [ ] All heated swimming pools must have an on/off heater switch and require a cover unless over 20% of the heating energy is from non-depletable sources. Pool pumps require a time clodL 1 Heating and Cooling Piping Insulation: [ l HVAC piping conveying fluids above 105 OF or chilled fluids below 55 OF must be insulated to the ( levels in Table 2. Table 1: Minimum Insulation Thickness for Circulating Hot Water Pipes. Insulation Thickness in Inches by Pipe Sizes Heated Water Non-Circulating Runouts Circulating Mains and Runouts Temperature(F) Up to 1" Up to 1.25" 1.5"to 2.0" Over 2" 170-180 0.5 1.0 1.5 2.0 140-160 0.5 0.5 1.0 1.5 100-130 0.5 0.5 0.5 1.0 Table 2: Minimum Insulation Thickness for HVAC Pipes. Fluid Temp. Insulation Thickness in Inches by Pipe Sizes Piping System Types Range(F) 2"Runouts 1"and Less 1,25"to 2" 2.5"to 4" Heating Systems Low Pressure/Temperature 201-250 1.0 1.5 1.5 2.0 Low Temperature 120-200 0.5 1.0 1.0 1.5 Steam Condensate(for feed water) Any 1.0 1.0 1.5 2.0 Cooling Systems Chilled Water,Refrigerant, 40-55 0.5 0.5 0.75 1.0 and Brine Below 40 1.0 1.0 1.5 1.5 NOTES TO FIELD (Building Department Use Only)